NV2410N
NV2420N
NV3610N
NV3620N
NV4820N
NV4820CN
NW3620N
NW4820N
B
D
F
3
G
H
I
4
(Original instructions)
ENGLISH
Intended use
Your Black & Decker Dustbuster® handheld vacuum cleaner has been designed for
light dry vacuum cleaning purposes (NV2410N, NV2420N, NV3610N, NV3620N,
NV4820N & NV4820CN). This appliance is intended for household use only.
Your Black & Decker Dustbuster® handheld vacuum cleaner has been designed for
light wet and dry vacuum cleaning purposes (NW3620N & NW4820N). This appliance is
intended for household use only.
Safety instructions
Warning! Read all safety warnings
@
and all instructions.Failure to follow the
warnings and instructions listed below may result
in electric shock, fire and/or serious injury.
Warning!When using battery-powered ap-
@
pliances, basic safety precautions, including the
following, should always be followed to reduce
the risk of fire, leaking batteries, personal injury
and material damage.
u
u
Read all of this manual carefully before using the appli-
ance.
The intended use is described in this manual. The use
of any accessory or attachment or the performance
of any operation with this appliance other than those
recommended in this instruction manual may present a
risk of personal injury.
u
Retain this manual for future reference.
Using your appliance
u
Do not use the appliance to pick up liquids or any mate-
rials that could catch fire.
u
u
u
Do not use the appliance near water.
Do not immerse the appliance in water.
Never pull the charger lead to disconnect the charger
from the socket. Keep the charger lead away from heat,
oil and sharp edges.
5
(Original instructions)
ENGLISH
u
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or in-
struction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
InBsepfoercetuisoen, cahencdk threepapapilriasnce for damaged or defec-
u
tive parts. Check for breakage of parts, damage to
switches and any other conditions that may affect its
operation.
u
u
u
u
Do not use the appliance if any part is damaged or
defective.
Have any damaged or defective parts repaired or
replaced by an authorized repair agent.
Regularly check the charger lead for damage. Replace
the charger if the lead is damaged or defective.
Never attempt to remove or replace any parts other
than those specified in this manual.
Additional safety instructions
Residual risks.
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from mis-
use, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks can not be avoided.
These include:
u
u
u
Injuries caused by touching any moving parts.
Injuries caused by touching any hot parts.
Injuries caused when changing any parts or accesso-
ries.
6
(Original instructions)
ENGLISH
u
Injuries caused by prolonged use of the appliance.
When using any appliance for prolonged periods ensure
you take regular breaks.
Batteries and chargers
Batteries
u
u
u
u
Never attempt to open for any reason.
Do not expose the battery to water.
Do not expose the battery to heat.
Do not store in locations where the temperature may
exceed 40°C.
u
u
Charge only at ambient temperatures between 10°C
and 40°C.
Charge only using the charger provided with the appli-
ance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
Do not damage/deform the battery pack either by punc-
ture or impact, as this may create a risk of injury and
fire.
u
u
u
u
Do not charge damaged batteries.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe
the liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions
u
Wbaerlnowin. g!The battery fluid may cause personal injury
or damage to property. In case of skin contact, immediate-
ly rinse with water. If redness, pain or irritation occurs seek
medical attention. In case of eye contact, rinse immedi-
ately with clean water and seek medical attention.
Chargers
Your charger has been designed for a specific
voltage. Always check that the mains voltage
corresponds to the voltage on the rating plate and
the information in the technical data table.
7
(Original instructions)
ENGLISH
Warning!Never attempt to replace the charger unit
with a regular mains plug.
u
Use your Black & Decker charger only to charge the
battery in the appliance/tool with which it was supplied.
Other batteries could burst, causing personal injury and
damage.
u
u
Never attempt to charge nonrechargeable batteries.
If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised Black & Decker
Service Centre in order to avoid a hazard.
Do not expose the charger to water.
u
u
u
u
Do not open the charger.
Do not probe the charger.
The appliance/tool/battery must be placed in a well
ventilated area when charging.
Electrical safety
Your charger has been designed for a specific
voltage. Always check that the mains voltage cor-
responds to the voltage on the rating plate. Never
attempt to replace the charger unit with a regular
mains plug.
Symbols on the charger
Read all of this manual carefully before using the
appliance.
This tool is double insulated; therefore no earth
#
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Short circuit proof safety isolating transformer.
The mains supply is electrically separated from
the transformer output.
w
8
(Original instructions)
ENGLISH
The charger automatically shuts off if the ambi-
ent temperature becomes too high. As a con-
sequence the charger will be inoperable. The
charging base must be disconnected from the
mains supply and taken to an authorised service
centre for repair.
x
The charging base is intended for indoor use
only.
$
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Dust bowl
4. Charger
5. Charging bracket
Fig. A
6. Dry pick up cloth filter (NV2410N, NV2420N, NV3610N, NV3620N, NV4820N &
NV4820CN Only)
7. Pre-filter (NV2410N, NV2420N, NV3610N, NV3620N, NV4820N & NV4820CN
Only)
8. Wet/Dry foam insert (NW3620N & NW4820N Only)
9. Wet/Dry deflector (NW3620N & NW4820N Only)
Fig. B
10. Squeegee (NW3620N & NW4820N Only)
11. Brush tool (NV2420N, NV3620N, NV4820N & NV4820CN Only)
12. Crevice tool (NV2420N, NV3620N, NV4820N & NV4820CN Only)
Note: The accessories can be stored by fitting them into the front of the appliance. For
models that are supplied with both a brush and a crevice tool, first fit the brush into the
front of the appliance then fit the crevice tool into the brush for storage.
Installation
Wall Mounting (fig. C)
The product can be attached to a wall to provide a convenient storage and charging
point for the appliance.
When fixing to a wall, make sure that the fixing method is suitable for the wall type and
is appropriate to the weight of the appliance.
u Mark the location of the screw holes (within reach of an electrical outlet for charging
the vac while it is on the wall bracket).
u Fix the mounting bracket to the wall using appropriate scres and plugs for the type
of wall and weight of the appliance.
u Hang the appliance on the wall by placing the opening on the base of the vac over
the hooks in the wall mount charging bracket.
9
(Original instructions)
ENGLISH
Assembly
Accessories (fig .B)
These models may be supplied with some of the following accessories:
u A squeege tool (10) for wet use on hard surfaces.
u A brush tool (11) for furniture and stairs.
u A crevice tool (12) for confined spaces.
Fitting (Fig. D)
u Insert the appropriate accessory into the front of the appliance. Make sure that the
accessory is pushed fully in.
Use
u Before first use, the battery must be charged for at least 24 hours.
u Place the appliance on the charging bracket whenever it is not in use.
Warning! Before charging, be sure to empty all liquid contents and dry thoroughly, to
avoid damage to your appliance.
Charging the battery (Fig. C)
u Make sure that the appliance is switched off. The battery will not be charged with
the on/off switch in the on position.
u Place the appliance on the charging bracket (5).
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge for at least 21 hours.
While charging, the charger may become warm. This is normal and does not indicate a
problem. The appliance can be left connected to the charger indefinitely.
Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40
°C.
Note: Ensure the appliance is fully seated onto the charging base. If the appliance is
not fully seated then the appliance will not charge.
Switching on and off (fig. E)
u To switch the appliance on, slide the on/off switch (1) forward to position 1.
u To switch the appliance off, slide the on/off switch (1) back to position 0.
Dry pick up (NV2410N, NV2420N, NV3610N, NV3620N, NV4820N &
NV4820CN Only)
u For everyday spills of dry material.
Wet and dry pick up (NW3620N & NW4820N Only)
u For everyday spills of dry material, use your appliance without the squeegee acces-
sory.
Warning! Your product is designed for light spills only.
u This appliance can also be used to pick up everyday liquid spills. Use the squeegee
accessory on non-absorbent, hard surfaces. On absorbent surfaces, such as
carpet, your appliance will pick up wet spills better without the accessory.
u For best performance on hard surface wet pickups, insert squeegee into the bowl
nozzle opening.
u For best results when using this accessory, hold the appliance at an angle of 45°
and pull it slowly towards you.
u Do not fill the bowl beyond the end of the intake chute. If there is any liquid in the
bowl, do not turn the unit upside down, sideways, point the nozzle upward, or shake
the vac excessively.
10
(Original instructions)
ENGLISH
u After picking up liquid substances clean the appliance and filter immediately. Mold
and mildew may form if the unit is not properly cleaned after wet pickups.
u Before charging, be sure to empty all liquid contents and dry thoroughly, to avoid
damage to your appliance.
Optimising the suction force
In order to keep the suction force optimised, the filters must be cleared regularly during
use.
Emptying and cleaning the product.
Removing the dust bowl and filters (fig. F & G).
Warning! The filters are re-usable and should be cleaned regularly.
u Press the bowl release button (2) and pull the dust bowl (3) straight off.
u While holding the dust bowl over a bin or sink, pull out the filter to empty the con-
tents of the bowl.
u To replace the dust bowl, place it back onto the handle until it “clicks” firmly into
position.
Warning! Never use the appliance without the filters. Optimum dust collection will only
be achieved with clean filters.
Foam insert (fig. H) (NW3620N & NW4820N Only)
u Place the foam insert (8) into the centre of the wet/dry deflector (9).
Warning! Never use the appliance for wet applications without the water deflector and
foam insert fitted.
Pre-filter (fig. I) (NV2410N, NV2420N, NV3610N, NV3620N, NV4820N &
NV4820CN Olny)
The Filter and pre-filter can be separated to allow better cleaning.
u Twist the pre-filter (7) in an anti-clockwise direction and lift from the filter (6).
Cleaning the dust bowls and filters
u The dust bowls and filters can be washed in warm soapy water.
u Make sure that the filters and the dust bowl are dry before re-fitting.
Replacing the filters
The filters should be replaced every 6 to 9 months and whenever worn or damaged.
Replacement filters are available from your Black & Decker dealer:
For models: NV2410N, NV2420N, NV3610N, NV3620N, NV4820N & NV4820CN use
filter part number FLVD10-XJ
For models: NW3620N & NW4820N use filter part number FLWD10-XJ
Maintenance
Your Black & Decker corded/cordless appliance/tool has been designed to operate over
a long period of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/ cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/tool if the appliance/tool
has a separate battery pack.
u Or run the battery down completely if it is integral and then switch off.
u Unplug the charger before cleaning it. Your charger does not require any mainte-
nance apart from regular cleaning.
11
(Original instructions)
ENGLISH
u Regularly clean the ventilation slots in your appliance/tool/charger using a soft
brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do not use any abrasive or
solvent-based cleaner.
Protecting the environment
Separate collection. This product must not be disposed of with normal house-
Z
hold waste.
Should you find one day that your Black & Decker product needs replacement, or if it is
of no further use to you, do not dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging allows materials to be
z
recycled and used again. Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical products from the
household, at municipal waste sites or by the retailer when you purchase a new
product.
Black & Decker provides a facility for the collection and recycling of Black & Decker
products once they have reached the end of their working life. To take advantage of this
service please return your product to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest authorised repair agent by contacting your
local Black & Decker office at the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our after-sales service and
Battery
If you want to dispose of the product yourself, the battery must be removed as
Z
described below and disposed of in accordance with local regulations.
u Preferably discharge the battery by operating the appliance until the motor stops.
u Press the bowl release button (2) and remove the dust bowl (5).
u Remove the five screws holding the body of the appliance together.
u Lift the housing cover away from the assembly.
u Detach all lead connections from the battery pack.
u Remove battery pack and motor assembly.
u Place the battery pack and motor assembly in suitable packaging to ensure that the
terminals cannot be short-circuited.
u Take the battery pack and motor assembly to your service agent or to a local
recycling station.
Once removed, the battery cannot be refitted.
12
(Original instructions)
ENGLISH
Technical data
NV2410N
(H1)
NV3610N
(H1)
NV4820N
NV4820CN
(H1)
(H1)
NV2420N
(H1)
NV3620N
(H1)
NW4820N
(H1)
NW3620N
(H1)
Voltage
Battery
Weight
Charger
Vdc
2.4
3.6
4.8
4.8
Type
kg
NiMH
0.66
NiMH
0.74
NiMH
0.77
NiMH
0.8
SSC-
VA035015D
BA035015D
VA050020D
BA050020D
VA070015D
BA070015D
180008EU
SSC-
180008UK
Input voltage
Vac
230
230
5ac
230
7ac
100-240
27dc
Output voltage
Current
V
3.5ac
mA
150
14
200
14
150
14
85
21
Approximate
charge time
h
Weight
kg
0.2
0.21
0.2
0.06
Guarantee
Black & Decker is confident of the quality of its products and offers an outstanding
guarantee. This guarantee statement is in addition to and in no way prejudices your
statutory rights. The guarantee is valid within the territories of the Member States of the
European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty materials, workmanship
or lack of conformity, within 24 months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products subjected to fair wear and tear or
replace such products to ensure minimum inconvenience to the customer unless:
u The product has been used for trade, professional or hire purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign objects, substances or ac-
cidents;
u Repairs have been attempted by persons other than authorised repair agents or
Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of purchase to the seller or an
authorised repair agent. You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the address indicated in this
manual. Alternatively, a list of authorised Black & Decker repair agents and full details of
Decker product and to be kept up to date on new products and special offers. Further
information on the Black & Decker brand and our range of products is available at www.
blackanddecker.co.uk
13
ENGLISH
Do not forget to register your product!
send your name, surname and product code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Slough, Berkshire SL1 3YD
90595665 REV-0
02/2013
|