ZVB30SH/BH/WH – GE Monogram 30" Telescopic Downdraft Vents
Dimensions and Specifications (in inches)
Separate Raise/Lower Switch
2"
30"
8-1/2"
Lift
28-1/2"
7-1/2"
2-1/4"
All 30” models are equipped with a separate raise/lower switch. The switch must be installed
in a separate location outside of the vent and cooktop cutout.
3-1/8"
6-1/4"
27"
3-3/4"
Countertop Requirements
Before you begin you must:
Countertops must have a deep flat surface to
accommodate the cooktop and the vent.
Countertops with a rolled edge and backsplash
may not provide the flat surface area required.
1. Review countertop dimension illustrations
to be sure you will have enough flat
countertop surface depth.
10-1/2"
3-3/8"
7-1/8"
2. Check to be sure that the total countertop
depth required (including minimum cutout
to front edge depth) allows enough space
for a backsplash.
Base Cabinet Requirements
The base cabinet must be deep enough to
accommodate the minimum clearance to the
front edge of the countertop, the cooktop
burner box and the vent.
3. Review the cabinet illustration. Check to
be sure that the interior cabinet depth will
house the cooktop burner box, the vent and
the cutout clearance from the front.
Downdraft Vent and Cooktop Cutout
The installation of these downdraft vents
with any Monogram cooktop requires careful
consideration. For accurate planning,
review the individual dimension drawings
for the combined vent and Monogram
cooktop installation.
4. When countertop and cabinet depth present
a problem, review Creative Solutions.
5. Carefully review the installation instructions
packed with product or available online at
With careful planning you can achieve a
custom look with minimal adjustments.
For answers to your Monogram,® GE Profile™ or
Listed by
Underwriters
Laboratories
GE® appliance questions, visit our website at
GEAppliances.com or call GE Answer Center®
service, 800.626.2000.
R
Specification Created 10/03
130658
ZVB30SH/BH/WH – GE Monogram 30" Telescopic Downdraft Vents
Venting Options
The downdraft vent is shipped with the
discharge outlet pointing straight down
and can be changed to a left- or right-side
discharge. For even more flexibility, the entire
blower and mounting plate can be adjusted
3-1/2" to the left or right sides.
Discharge Down
(As Supplied)
Discharge Left
Discharge Right
Electrical and Gas Locations
Plan the placement of the electrical outlet
and gas (if used) carefully. Gas or electrical
outlets cannot be located on the back wall of
the cabinet because they may interfere with
the downdraft plenum.
Do Not Locate Gas or Electrical
Connections Within Shaded Area
• Install a standard electrical outlet within
reach of the vent’s two-foot-long power
cord. Locate the outlet inside the cabinet
on the right side wall.
• If the vent is installed in combination with a
Monogram® gas cooktop, it may operate
from the same 120V standard duplex outlet.
• If the vent is installed in combination with a
Monogram electric cooktop, the vent must
operate from a separate 120V outlet.
29-1/2"
Electrical
Outlet
12" Above
Cabinet Floor
34" for 36" Models
28-1/2" for 30" Models
Listed by
Underwriters
Laboratories
R
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
GEAppliances.com or call GE Answer Center®
service, 800.626.2000.
Specification Created 10/03
130658
ZVB30SH/BH/WH – GE Monogram 30" Telescopic Downdraft Vents
Features and Benefits
• 30" Telescopic downdraft system
• 500 CFM performance
• Remote-mounted control
• Variable-speed fan with slide control
• Raises to 8-1/2" over cooktop surface
• Retracts when not in use
• Removable grease filters
• 3-1/4" x 10" rectangular duct
• Optional remote blower capabilities
• Stainless steel vent body
• Minimum 6" round duct capabilities
• Model ZVB30SHSS – Stainless steel (shown)
• Model ZVB30WHWW – White on white
• Model ZVB30BHBB – Black on black
Specification Created 10/03
130658
|